Block Wall Cost Calculator (Tucson Area, 2026)
Price a new or replacement block wall in the Tucson metro from published 2026 ranges.
Prices last reviewed November 2026
Wall details
Standard CMU privacy wall. Includes excavation, footing, rebar, grout, and labor.
Prices use Tucson metro ranges for every city. The city chooses the contractor list.
Estimated cost
$5,500 to $12,500
$55 to $125 per linear foot
| Item | Low | High |
|---|---|---|
| Plain block wall (100 ft at 6 ft) | $5,500 | $12,500 |
- A permit is not included. Tucson, Pima County, Oro Valley, Marana and Sahuarita each set their own permit rules; see /block-wall-permits.
- Caliche and tight access can raise the cost.
- Prices change, so get three written bids.
Estimate only, based on published 2026 price ranges. Not a quote. South AZ Block Walls is a directory and does not do the work. Get at least three written bids.
Sources
Prices last reviewed November 19, 2026.
- Tucson masonry contractor guide
- Phoenix-area figure (New Era Masonry 2026, via https://phoenixfenceguide.com/block-wall-cost-breakdown/)
- HomeGuide 2026 concrete removal, as cited on /cost-guide
- Phoenix-area figure
- Tucson masonry contractor, block wall repair
- Phoenix figure adjusted 10% lower for Tucson labor: New Era Masonry, repair costs
- Phoenix figure adjusted 10% lower for Tucson labor: New Era Masonry, cracks and cost
AyX Estimator puts a typical 100 ft, 6 ft Tucson wall at 5,850 to 11,500 (https://ayxestimator.com/cost/block-wall-installation-cost-arizona). This comparison is not used in the calculation.
Frequently asked questions
What does a 6 ft block wall cost per linear foot in the Tucson metro?
A standard 6 ft plain CMU privacy wall runs about $55 to $125 per linear foot installed in the Tucson metro. That range includes excavation, footing, rebar, grout, and labor. The calculator scales it for other heights. Split-face block runs about $70 to $150 per linear foot at the same base height. These are published 2026 ranges, not a quote.
Does the price include stucco?
No. The $55 to $125 per linear foot range is plain block only. Stucco on one side adds about $6 to $9 per square foot of wall face. Paint only, without stucco, adds about $2 to $4 per square foot for one side.
What does demolition add?
Choosing replace adds about $5 to $16 per linear foot for demolition across the full length of the wall. That figure is HomeGuide 2026 concrete removal, as cited on /cost-guide. Haul-off and landfill fees are often extra and are not included.
How much does block wall repair cost?
Repair is priced per job. Minor mortar repointing runs about $250 to $800. Replacing individual blocks runs about $41 to $81 per block. Rebuilding the top 1 to 3 courses runs about $41 to $86 per linear foot. Rebuilding a small damaged section runs about $1,350 to $3,150. A failed footing, with the wall rebuilt on a new footer, runs about $2,700 to $5,400 and can run higher. Stucco and paint blending adds about $270 to $720, and a drainage or weep correction adds about $360 to $1,350. A minimum service call is $225 to $360. Repointing is a Tucson masonry figure. The other repair ranges are Phoenix figures adjusted 10% lower for Tucson labor.
Do I need a permit?
It depends on your city, and the permit fee is not included. Tucson, Pima County, Oro Valley, Marana and Sahuarita each set their own permit rules; see /block-wall-permits. An 8 ft wall usually needs 8-inch block, engineering and a permit, so quotes vary more.
How accurate is this calculator?
Estimate only, based on published 2026 price ranges. Not a quote. South AZ Block Walls is a directory and does not do the work. Get at least three written bids. Caliche and tight access can raise the cost.